No hay artículos en el carro
No hay artículos en el carroDescripción del producto
Característica:
- 1. Acero inoxidable 304 de alto grado seleccionado, a prueba de herrumbre y anticorrosión.
- 2. La barra de sujeción de goma puede sujetar firmemente la pieza de trabajo sin dañarla.
- 3. Base fija de 4 agujeros para una sujeción más estable.
- 4. El mango envuelto en plástico hace que la operación sea cómoda y fácil.
- 5. Diseño de estructura de palanca, ahorrando tiempo y esfuerzo.
Wanderer
Comentado en los Estados Unidos el 9 de agosto de 2024
I use a two single ramp system to load my mobility scooter into my truck. The ramps are narrow and subject to being out of parallel. I obtained an adjustable stud holder but it was limited to either 12 in. or 16 in. spacing and I needed variable spacing. Ordered this small toggle hold down clamp, removed the thumb screw for 12/16 in. original settings and epoxied the clamp to the stud spacer. Works great and can be adjusted to sizes I need. Works great.
Customer
Comentado en los Estados Unidos el 22 de octubre de 2024
these things are so hard to figure the right size a pic in Somone's hand or next to something to get the size
Castillo G
Comentado en México el 3 de junio de 2023
Me gusto por que funciona al 100% en para modelismo. Ya para trabajos de carpintería existe el mismo modelo pero 4 veces mas grande para sujetar mas de 45 a 75 kilos o más.
Dave Rentz
Comentado en los Estados Unidos el 1 de julio de 2021
Pros: It's very well made! And; unlike 99% of what comes out of China, claiming to be stainless steel / aluminum; it actually is! Even the rubber bumper is quite stout. It's -a-l-m-o-s-t- as though they mean this to be used for actual work!Cons: I'm not sure who would have a use for such a...petite...clam. I took one star off for that, because it was not at all made obvious that this clamp was so small. I just assumed it would be somewhere within the size-range of "useful". I didn't realize it was sized to "teddy-bear-scale".
JOSE DE JESUS VERDUZCO
Comentado en México el 1 de febrero de 2021
no me llego completo, a una abrazadera le falto la punta.
D. Smart
Comentado en los Estados Unidos el 19 de octubre de 2021
I does what it is intended to do. This is a small clamp, some will say miniature.The black rubber tip is molded onto a philips screw. So far so good. In my case, clamped onto finished wood, the rubber stuck to the finished wood and pulled off of the screw. There does not seem to be any way to put this back on to the screw. The wood finish was well dried wood primer. After the two parts parted ways, the rubber part the proceeded to fall off of the primed wood. As it recovered from its as clamped distortion, it simply detached and fell to the floor. So the adhesion was not great.The clamp is used to clamp an attic ladder hatch closed. The clamps spends a long time locked down.I like the stainless steel finish and as a visible item in my house, I know it will not age to some old gray oxidized state over the years.
Productos recomendados
Mex $1,042.82
Mex $ 573 .00 Mex $573.00
Mex $273.00
Mex $ 152 .00 Mex $152.00
Mex $595.00
Mex $ 297 .00 Mex $297.00
Mex $596.04
Mex $ 286 .00 Mex $286.00
Mex $252.00
Mex $ 138 .00 Mex $138.00